Can't boot system from my Windows CD

Inspektor · 07-04-2005, 09:19 PM

okay, this is pretty weird. I don't even know where to begin.

I think the whole problem started when I tried to clone my 10gb Seagate HDD (my system drive) to the new WD 80gb HDD using Norton Ghost 9.0 It did work, however I forgot to check the "Copy MBR" option, so I had to did it again. This time it didn't work. It said something about my Disk 1 (my source 10gb drive) layout not matching the OS information (?). So I thought "oh well, I'll just install Windows from scratch on the new drive using my Windows CD". To my surprise, i wasn't able to get it to boot. I set all the necessary options in BIOS (booting devices and stuff), and tried again (with and without my current system disk). It just didn't work. It would say "no operating system found" with the HDD disconnected, and when it was connected, Windows would just boot from it (even though the booting sequence in my BIOS looks like CD-CD-CD). I know my CD is fine, because I had used it like 3 or 4 times to install Windows in the past.

Yesterday, I borrowed my friend's Windows CD, just for the heck of it. This time, it said "NTLDR not found" when I disconnected my primary HDD. With the HDD connected, it just loaded Windows off it.

I am really at loss. I am beginning to think it's some kind of hardware problem with my mobo or/and BIOS, but still, when using my old 10 giger WIndows loads just fine and I have no problems running the system, but I really want to replace this old drive with my new WD one.

just a minute ago I tried disconnecting ALL my hard drives from the on-board controler, and guess what, my computer started with the Windows CD just fine.... however, when I connected ANY of my HDDs, it was the same thing again - either it would say "no operating system found", or just boot from my current system HDD. I think I might have some weird problem with my IDE controlers, but I am really not sure what to think any more

I tried all possible configurations - one HDD and one CD drive, one HDD and two CD drives, one CD drive and one HDD on the same cable, it was all the same - whenever there's a HDD connected, I just can't get the system to boot from the WIndows CD

Dave35k · 07-04-2005, 11:37 PM

hi m8 when you first start your pc press delete to enter bios and look under the menus (change from pc to pc) usually called something like advanced bios settings there is a boot sequence make the 1st device your cd rom drive then save and exit with the win xp disk in it should boot off it, your hdds have to be connected to install windows on. hope this helps Dave

07-04-2005, 09:19 PM	#1 (permalink) Top
Inspektor Geek Trainee Join Date: Apr 2005 Posts: 1 Status: Offline	Can't boot system from my Windows CD okay, this is pretty weird. I don't even know where to begin. I think the whole problem started when I tried to clone my 10gb Seagate HDD (my system drive) to the new WD 80gb HDD using Norton Ghost 9.0 It did work, however I forgot to check the "Copy MBR" option, so I had to did it again. This time it didn't work. It said something about my Disk 1 (my source 10gb drive) layout not matching the OS information (?). So I thought "oh well, I'll just install Windows from scratch on the new drive using my Windows CD". To my surprise, i wasn't able to get it to boot. I set all the necessary options in BIOS (booting devices and stuff), and tried again (with and without my current system disk). It just didn't work. It would say "no operating system found" with the HDD disconnected, and when it was connected, Windows would just boot from it (even though the booting sequence in my BIOS looks like CD-CD-CD). I know my CD is fine, because I had used it like 3 or 4 times to install Windows in the past. Yesterday, I borrowed my friend's Windows CD, just for the heck of it. This time, it said "NTLDR not found" when I disconnected my primary HDD. With the HDD connected, it just loaded Windows off it. I am really at loss. I am beginning to think it's some kind of hardware problem with my mobo or/and BIOS, but still, when using my old 10 giger WIndows loads just fine and I have no problems running the system, but I really want to replace this old drive with my new WD one. just a minute ago I tried disconnecting ALL my hard drives from the on-board controler, and guess what, my computer started with the Windows CD just fine.... however, when I connected ANY of my HDDs, it was the same thing again - either it would say "no operating system found", or just boot from my current system HDD. I think I might have some weird problem with my IDE controlers, but I am really not sure what to think any more I tried all possible configurations - one HDD and one CD drive, one HDD and two CD drives, one CD drive and one HDD on the same cable, it was all the same - whenever there's a HDD connected, I just can't get the system to boot from the WIndows CD

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
help - my computer wont boot into windows	drasifus	Windows OS's	1	23-02-2005 09:11 PM
Anytime I enable 4x or 8x my next boot of windows will have colored dots every where.	SbkNomed	Video Cards, Displays and TV Tuners	6	14-01-2005 02:46 AM
Windows 98 Boot Issues... Help!	chief	Windows OS's	8	02-11-2004 06:12 PM
Windows system repair.	zeus	Windows OS's	13	12-02-2004 02:31 PM
after i upgraded gigabyte bios the system does not boot at all	kariem2k	CPU, Motherboards and Memory	3	22-11-2003 05:43 PM

07-04-2005, 11:37 PM	#2 (permalink) Top
Dave35k Hacker Join Date: Dec 2004 Age: 19 Male Posts: 312 Times Helpful: 13 My Mood: Cool Status: Offline My Computer	hi m8 when you first start your pc press delete to enter bios and look under the menus (change from pc to pc) usually called something like advanced bios settings there is a boot sequence make the 1st device your cd rom drive then save and exit with the win xp disk in it should boot off it, your hdds have to be connected to install windows on. hope this helps Dave

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)