Ugrading my HP power supply

ala380 · 04-07-2007, 01:50 PM

I am sorry if questions like this have been asked before but I didn't anything that was really relevant to my question. About 6 months ago I was looking into building/having built a new pc. I was out and about one day and stumbled across an HP m7640n media center pc for a really good price so I bought it. I know that prebuilt pcs are kinda of taboo but it is actually a pretty good machine. When buying it I knew that I was going to have to replace the video card at some point but I wasn't really prepared for was the measly 300w power supply. I have confirmed with HP that this is indeed a standard ATX power supply and that it can be replaced but they told me that the motherboard may not be able to handle anything over 300 watts. Now I know that what they are saying is that the motherboard hasn't been tested with anything over 300 watts so my question is...Does anyone forsee any real true problems with popping in a 500 watt power supply into this thing? I do not have a fully loaded system and I probably don't need 500 watts at this point but I would rather be safe than sorry. Is there a true chance that I will fry my motherboard or do you think HP is just being overly cautious. Thanks to anyone who can help me with this. Here are the motherboard stats.

Motherboard description

Motherboard manufacturer's name: ASUS A8M2N-LA

CPU/Processor

Socket: AM2
Supports AMD Athlon 64, Athlon 64 X2, and Sempron processors

Front-side bus (FSB)

2000 MegaTransfers/second

Chipset

GeForce 6150 LE chipset

BIOS features

Award brand system BIOS
Keyboard combination to used to enter BIOS: F1

Form factor

Micro-ATX: 9.6 in X 9.6 in

Memory

Four 240-pin DDR2 DIMM sockets
Supports PC 4200 (533 MHz) and PC2 5300 (667 MHz) DDR2 DIMMs
Non-ECC memory only, unbuffered
Maximum HP/Compaq approved memory is 4 GB*

NOTE: *Actual available memory may be less
Expansion slots

Three PCI
One PCI Express x16 graphics

Video graphics

Integrated

Serial ATA

4 SATA connectors
Each connector supports 1 serial ATA-150 disk drive

Onboard audio

Built-in High Definition 8 channel audio
ALC888 CODEC

Onboard LAN

10/100 Marvell 88EC031

Back panel I/0 Listed in physical order from left to right:

One PS/2 keyboard port (purple)
One PS/2 mouse port (green)
One SPDIF (coaxial) out
One VGA port
One IEEE 1394
Four USB 2.0
One RJ-45 networking port
Audio ports:
o side speaker out (gray)
o rear speaker out (black)
o center/subwoofer (yellow orange)
o line in (light blue)
o line out (lime)
o microphone (pink)

Internal connectors

* One 24-pin ATX power connector
* One 4-pin ATX power connector
* Two PATA connectors
* Four SATA connectors
* One floppy drive connector
* Two 12v fan connectors for CPU fan and PC fan
* One 9-pin header for power button, reset button, power LED, and HDD LED
* One audio header for headphone-out and microphone-in
* One audio header for line input
* Two USB 2.0 connectors supporting 4 additional USB 2.0 ports
* One IEEE 1394 connector

Sniper · 05-07-2007, 07:50 PM

unless something went wrong with the power supply, I don't see why it won't work.

ala380 · 06-07-2007, 04:19 PM

Thanks for the reply Sniper. I was kind of figuring the same thing. I didn't really understand why the motherboard couldn't handle a higher power supply. That's HP support for you I guess.

Big B · 06-07-2007, 08:11 PM

Yeah, there's no reason why you couldn't use a PSU larger than 300W, save for an oversized unit like some 800W+ units are. If you have a micro ATX case, which I think you do, then you might run into a physical limitation imposed by the case. That's your biggest consideration.

ala380 · 08-07-2007, 02:59 PM

Thanks Big B. It's always good to have more opinions on the subject. My case is actually a mid size tower and the current supply that is in there is indeed a standard atx power supply (not a micro atx power supply and thankfully not some proprietary crap) so replacing it should not be an issue as far as size. Although I am thinking of transferring everything into a better case anyway. Thanks again for the help.

04-07-2007, 01:50 PM	#1 (permalink) Top
ala380 Geek Trainee Join Date: Feb 2007 Age: 28 Female Posts: 4 Status: Offline	Ugrading my HP power supply I am sorry if questions like this have been asked before but I didn't anything that was really relevant to my question. About 6 months ago I was looking into building/having built a new pc. I was out and about one day and stumbled across an HP m7640n media center pc for a really good price so I bought it. I know that prebuilt pcs are kinda of taboo but it is actually a pretty good machine. When buying it I knew that I was going to have to replace the video card at some point but I wasn't really prepared for was the measly 300w power supply. I have confirmed with HP that this is indeed a standard ATX power supply and that it can be replaced but they told me that the motherboard may not be able to handle anything over 300 watts. Now I know that what they are saying is that the motherboard hasn't been tested with anything over 300 watts so my question is...Does anyone forsee any real true problems with popping in a 500 watt power supply into this thing? I do not have a fully loaded system and I probably don't need 500 watts at this point but I would rather be safe than sorry. Is there a true chance that I will fry my motherboard or do you think HP is just being overly cautious. Thanks to anyone who can help me with this. Here are the motherboard stats. Motherboard description Motherboard manufacturer's name: ASUS A8M2N-LA CPU/Processor Socket: AM2 Supports AMD Athlon 64, Athlon 64 X2, and Sempron processors Front-side bus (FSB) 2000 MegaTransfers/second Chipset GeForce 6150 LE chipset BIOS features Award brand system BIOS Keyboard combination to used to enter BIOS: F1 Form factor Micro-ATX: 9.6 in X 9.6 in Memory Four 240-pin DDR2 DIMM sockets Supports PC 4200 (533 MHz) and PC2 5300 (667 MHz) DDR2 DIMMs Non-ECC memory only, unbuffered Maximum HP/Compaq approved memory is 4 GB* NOTE: Actual available memory may be less Expansion slots Three PCI One PCI Express x16 graphics Video graphics Integrated Serial ATA 4 SATA connectors Each connector supports 1 serial ATA-150 disk drive Onboard audio Built-in High Definition 8 channel audio ALC888 CODEC Onboard LAN 10/100 Marvell 88EC031 Back panel I/0 Listed in physical order from left to right: One PS/2 keyboard port (purple) One PS/2 mouse port (green) One SPDIF (coaxial) out One VGA port One IEEE 1394 Four USB 2.0 One RJ-45 networking port Audio ports: o side speaker out (gray) o rear speaker out (black) o center/subwoofer (yellow orange) o line in (light blue) o line out (lime) o microphone (pink) Internal connectors One 24-pin ATX power connector * One 4-pin ATX power connector * Two PATA connectors * Four SATA connectors * One floppy drive connector * Two 12v fan connectors for CPU fan and PC fan * One 9-pin header for power button, reset button, power LED, and HDD LED * One audio header for headphone-out and microphone-in * One audio header for line input * Two USB 2.0 connectors supporting 4 additional USB 2.0 ports * One IEEE 1394 connector

05-07-2007, 07:50 PM	#2 (permalink) Top
Sniper Administrator Join Date: Oct 2001 Age: 24 Male Posts: 4,420 Times Helpful: 116 My Mood: Bored Status: Offline My Computer	unless something went wrong with the power supply, I don't see why it won't work. __________________ Zone 365 \| F@H Team \| Team Stats \| Use The Thank You System \| My Groups: Manchester United \| Apple

06-07-2007, 08:11 PM	#4 (permalink) Top
Big B HWF Godfather Join Date: Dec 2001 Age: 28 Male Posts: 9,636 Times Helpful: 585 My Mood: Devilish Status: Offline My Computer	Yeah, there's no reason why you couldn't use a PSU larger than 300W, save for an oversized unit like some 800W+ units are. If you have a micro ATX case, which I think you do, then you might run into a physical limitation imposed by the case. That's your biggest consideration. __________________ Hardware Forums\|HWF Rules\|My DVD's\|PSU FAQ\|HWF Folding Team\|2CPU

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Hot Power Supply	kayber	Power Supplies and UPS's	1	05-03-2007 09:27 AM
what is my power supply	blade	Power Supplies and UPS's	15	18-02-2007 07:07 PM
ugh... do i need a power supply??	jjd228	New Build / Upgrade Advice	19	28-12-2006 07:56 PM
which power supply is best???	eshban	New Build / Upgrade Advice	3	07-10-2005 12:54 PM
New power supply	evanjanis	Power Supplies and UPS's	1	29-10-2004 10:36 PM

06-07-2007, 04:19 PM	#3 (permalink) Top
ala380 Geek Trainee Join Date: Feb 2007 Age: 28 Female Posts: 4 Status: Offline	Thanks for the reply Sniper. I was kind of figuring the same thing. I didn't really understand why the motherboard couldn't handle a higher power supply. That's HP support for you I guess.

08-07-2007, 02:59 PM	#5 (permalink) Top
ala380 Geek Trainee Join Date: Feb 2007 Age: 28 Female Posts: 4 Status: Offline	Thanks Big B. It's always good to have more opinions on the subject. My case is actually a mid size tower and the current supply that is in there is indeed a standard atx power supply (not a micro atx power supply and thankfully not some proprietary crap) so replacing it should not be an issue as far as size. Although I am thinking of transferring everything into a better case anyway. Thanks again for the help.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)