Overclocking with AMD 64

Discussion in 'Overclocking & Cooling' started by halfpipehippie, Aug 8, 2006.

  1. halfpipehippie

    halfpipehippie Geek Trainee

    Likes Received:
    0
    Trophy Points:
    0
    hey guys, ive heard that that atlon 64 overclocks a bit diffrently than the other CPU's out there, and because of this i need some help figureing it out, the tutorials always talk about FSB Memory clock speed, and CPU clock speed, but i plu see the CPU clock speed. ive raised the Clock speed to about 222Mhz and it runs at 2Ghz but i know i can get it better than this. what would i need to do to go beyond this point. at this point it fails to start windows, and even now occasionally it will restart the computer on its own will, usually when i do something CPU intesive. thanks guys
     
  2. Exfoliate

    Exfoliate Geek Trainee

    Likes Received:
    166
    Trophy Points:
    0
    Unfortunately not all processors are created equal. You're 3000+ isn't necessarially going to oc as well as someone elses unfortunately. There's just no standard set as to how far a chip with oc. Especially concidering it's not actually intended to go any further.
    There's 4 major factors at work here. First off, you're cpu. This is an easy one as I'm assuming it's a new processor and therefore has a Venice core. That's good as those generally have some good OC potential. Then there's you're ram, if it's cheapo no name bargin ram it's not going to give you very good yeilds oftentimes. Then the motherboard. I don't see that being a problem MSI makes decent boards and the nForce 4 line is concidered a decent overclocking platform. Cooling comes in as the most important factor here. Again I'm not really seeing a problem, that's a minor overclock and even the stock heatsink/fan is plenty to keep it in the 30's. If you are for some odd reason seeing cpu and system temperatures in the 60's then you might have a problem but otherwise cooling is not a factor either.
    What it comes down to is you might just have a cpu that doesn't oc very well. It's not unheard of by any means. There's no reason to increase the voltage really that I can see. Maybe a more experienced overclocker can shed some light here?
     
  3. izzy007

    izzy007 Big Geek

    Likes Received:
    0
    Trophy Points:
    0
    i wudnt reccomend increasing voltage becoz over time long term damage will be caused and the cpu's life is shortened.
     
  4. vol7ron

    vol7ron Guest

    Make sure you're overclocking correctly, but to me it sounds like your problem is in your RAM. Post a little more info on that, run MemTest and SiSoftware Sandra 2007
     
  5. vol7ron

    vol7ron Guest

    These days this isn't so much a problem. AMD, Intel, and motherboard manufacturers have done a good job in improving the materials that they build their chipsets with. I think they coat them in some kind of heat-resistant plastic, or material of the sort. Anyhow, unless your temperature is above 50 degrees it will not damage the chip. The real temperatures to worry about are the upper 50s and into the 60s, but most processors have a cut-off point that will shut yoru computer down if it gets to hot (and not allow a reboot until it has cooled off considerably).

    I was just laughing because your response reminds me of someone who sells processors and doesn't want people to overclock. "You have a 2.4.. if you want to get to a 2.7 you have to pump more vol7age into it and that can destroy your board and cpu, but i can sell you one for $300 more"

    The truth is people (enthusiasts/gamers) have increased the turnover rate of upgrading their hardware. Some go as far as to alway buy what's new (the extreme wealthy enthusiasts) - others upgrade every 2 to 3 years. What does this mean? Good you should ask.. even if the vol7age "did" have limit the lifetime of the cpu (however long that limit should be), it will more than likely be way after the time they decide to buy a whole new system.
     
  6. Merlin

    Merlin Geek Trainee

    Likes Received:
    1
    Trophy Points:
    0
    I would also like to know how to overclock an AMD 64. I have done some reading about it and I get confused with all the FSB:DRAM ratios, HTT multipliers etc... Any help on this?
     
  7. zeus

    zeus out of date

    Likes Received:
    0
    Trophy Points:
    36
    Northwood pentium 4s are rated at 1.5v but the intel datasheet gives a max voltage of 1.75v! To be honest I wouldnt like to crank mine up to 1.75v for the long term (I did do a voltage mod once to see if I could get a stable 33% OC but it wasnt stable) but Ive had it at 1.6v (1.65v in software readings) for years. No degradation, nothing.
     
  8. halfpipehippie

    halfpipehippie Geek Trainee

    Likes Received:
    0
    Trophy Points:
    0
    ok i have sisandra 2007 and i dont know what test to run to figure out the RAM details, but i can tell you that i have one PNY "OPTIMA MEMORY" nd one Corsair stick, both at 512, for Si sandra all the info as of now i could find was this...



    SiSoftware Sandra

    Mainboard
    Manufacturer : Jetway
    MP Support : 2 Processor(s)
    MPS Version : 1.40
    Model : NF-CK804
    System BIOS : 09/30/2005-NF-CK804-6A61FJ19C-00
    Chipset : nVidia nForce4 & Ultra ICP

    System Memory Controller
    Location : Mainboard
    Error Correction Capability : None
    Number of Memory Slots : 4
    Maximum Installable Memory : 16GB
    Bank0/1 - A0 : Empty
    Bank2/3 - A1 : Empty
    Bank4/5 - A2 : Empty
    Bank6/7 - A3 : Empty

    Chipset 1
    Model : Advanced Micro Devices (AMD) Athlon 64 / Opteron HyperTransport Technology Configuration
    Bus(es) : ISA PCI PCIe USB i2c/SMBus
    Version : 1.02
    Front Side Bus Speed : 2x 888MHz (1776MHz data rate)
    Maximum FSB Speed / Max Memory Speed : 2x 1000MHz / 2x 200MHz
    In/Out Width : 16-bit / 16-bit
    SMP - MP Capability : No
    IO Queue Depth : 8 request(s)

    Chipset 1 Hub Interface
    Type : HyperTransport
    Version : 1.02
    In/Out Width : 16-bit / 16-bit
    Speed : 2x 888MHz (1776MHz data rate)

    Logical/Chipset 1 Memory Banks
    Bank 2 : 512MB DDR-SDRAM 3.0-4-4-8 2CMD
    Bank 3 : 512MB DDR-SDRAM 3.0-4-4-8 2CMD
    Channels : 1
    Bank Interleave : 2-way
    Speed : 2x 222MHz (444MHz data rate)
    Multiplier : 1/9x
    Width : 128-bit
    Memory Controller in Processor : Yes
    Cores per Memory Controller : 1 Unit(s)
    Refresh Rate : 7.80µs
    Power Save Mode : No
    Fixed Hole Present : No

    Memory Module 1
    Type : 512MB DDR-SDRAM
    Technology : 16x(32Mx8)
    Speed : PC3200U 3.0-4-4-8
    Date of Manufacture : Saturday, December 25, 1999
    Set Timing @ 200MHz : 3.0-4-4-8
    Set Timing @ 167MHz : 2.5-3-3-7
    Set Timing @ 133MHz : 2.0-2-2-5

    Memory Module 2
    Manufacturer : Corsair
    Model : VS512MB400C3
    Type : 512MB DDR-SDRAM
    Technology : 16x(32Mx8)
    Speed : PC3200U 3.0-3-3-8
    Date of Manufacture : Saturday, December 25, 1999
    Set Timing @ 200MHz : 3.0-3-3-8

    Environment Monitor 1
    Model : NS LM78 ISA
    Mainboard Specific Support : No

    Cooling Device(s)
    Auto Fan Speed Control : No
    Chassis Fan Speed : 90000rpm
    CPU1 Fan Speed : 45000rpm

    Voltage Sensor(s)
    CPU1 Voltage : 0.02V
    CPU2 Voltage : 2.61V
    +3.3V Voltage : 0.24V
    +12V Voltage : 0.91V

    PCI Bus(es) on Hub 1
    Version : 2.30
    Number of Bridges : 5
    PCI Bus 0 : PCI (1/1x PCIClk)
    PCI Bus 1 : PCI (1/1x PCIClk)
    PCI Bus 2 : PCIe (3/1x PCIClk)
    PCI Bus 3 : PCIe (3/1x PCIClk)
    PCI Bus 4 : PCIe (3/1x PCIClk)
    PCI Bus 5 : PCIe (3/1x PCIClk)
    Number of PCIe Lanes : 20

    LPC Hub Controller 1
    Model : Nvidia Corp nForce4 PCI to ISA Bridge

    LPC Hub Controller 2
    Model : Nvidia Corp nForce4 SMBus

    USB Controller 1
    Model : Nvidia Corp nForce4 USB Controller
    Version : 1.00
    Interface : OHCI
    Channels : 10
    Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
    Legacy Emulation Enabled : No

    USB Controller 2
    Model : Nvidia Corp nForce4 USB 2.0 Controller
    Version : 2.00
    Specification : 1.00
    Interface : EHCI
    Channels : 10
    Companion Controllers : 1
    Supported Speed(s) : Low (1.5Mbps) Full (12Mbps) High (480Mbps)
    Addressing Support : 32-bit
    Legacy Emulation Enabled : No

    System SMBus Controller 1
    Model : nVidia MCP2+ B0 SMBus
    Version : 0A.02
    Advanced TCO Mode Enabled : No
    Slave Device Enabled : No
    PEC Support : No

    System SMBus Controller 2
    Model : nVidia MCP2+ B1 SMBus
    Version : 0A.02
    Advanced TCO Mode Enabled : No
    Slave Device Enabled : No
    PEC Support : No

    Expansion Slot(s)
    PCI0 (1h) : PCI 32-bit +5V PME Full-Length Available (Nvidia Corp nForce4 PCI to ISA Bridge)
    PCI1 (2h) : PCI 32-bit +5V PME Full-Length Available (Nvidia Corp nForce4 USB Controller)
    PCI2 (3h) : PCI 32-bit +5V PME Full-Length Available
    PCI3 (4h) : PCIe 32-bit +5V PME Full-Length Used (Jetway Information Co Ltd nForce4 AC'97 Audio Controller)
    PCI4 (5h) : PCIe 32-bit +5V PME Full-Length Used

    Port Connector(s)
    PRIMARY IDE : None - ATA / None
    SECONDARY IDE : None - ATA / None
    FDD : 8251 FIFO - Floppy Disk / None
    COM1 : Serial Port 16450 - 9 Pin Dual Inline / DB-9 pin male
    COM2 : Serial Port 16450 - 9 Pin Dual Inline / DB-9 pin male
    LPT1 : Parallel Port ECP/EPP - DB-25 pin female / DB-25 pin female
    Keyboard : Keyboard - PS/2 / PS/2
    PS/2 Mouse : Mouse - PS/2 / PS/2
    USB0 : USB - None / None

    Performance Tips
    Tip 2532 : Consider adding more CPUs for better utilisation.
    Notice 224 : SMBIOS/DMI information may be inaccurate.
    Tip 2511 : Some memory slots are free so the memory can be easily upgraded.
    Warning 100 : Large memory sizes should be made of Registered/Buffered memory.
    Tip 2546 : Large memory modules should be ECC/Parity.
    Warning 2540 : No APIC detected for MP system.
    Warning 2523 : Memory bus speed exceeds memory rated speed. Reduce memory bus speed.
    Warning 2542 : Memory bus speed exceeds Chipset rated speed. Reduce FSB/memory multiplier.
    Tip 2 : Double-click tip or press Enter while a tip is selected for more information about the tip.


    theres that lol
     
  9. zeus

    zeus out of date

    Likes Received:
    0
    Trophy Points:
    36
    They are some deadly chassis fans you've got. You could make a helicopter out of them! :)
     
  10. halfpipehippie

    halfpipehippie Geek Trainee

    Likes Received:
    0
    Trophy Points:
    0
    haha what do u mean? my fans can be set to run at a controlled speed in the BIOS but it makes a stupid hummmm and i just let it run at full speed
     
  11. zeus

    zeus out of date

    Likes Received:
    0
    Trophy Points:
    36
    90,000rpm for your chassis fan and 45,000rpm for your cpu fan.
    Even if they were 9,000 and 4,500 rpm they would be faster than everyone elses.
    Sandra has got it wrong.

    As far as im aware you need a resistor if your not running an electric motor at full speed. I dont know where that might be on a motherboard so you are probably best off running it at full whack anyway.
     
  12. halfpipehippie

    halfpipehippie Geek Trainee

    Likes Received:
    0
    Trophy Points:
    0
    can anyone help me with my overclocking problem?? i cant seem to get it stable at 2Ghz by just changing the Mhz speed to 222, i even tried to lower it but it still shut down. can ANYONE help me?
     
  13. beretta9m2f

    beretta9m2f Karate-Chop Action Gabe

    Likes Received:
    1
    Trophy Points:
    0
    Well i googled overcloking AMD 64, and found a lot of guides and stuff. For starters you should read this, i think it is explained decently (i've yet to overclock) i'm going to keep reading up on it so that i know what i'm doing before i start OCing. Try reading this to see if you missed anything.
     
  14. Willz

    Willz MiCrO$oFt $uK$ :D

    Likes Received:
    36
    Trophy Points:
    48
    ok, i dunno if this will help becouse i have a different motherboard and cpu to you, my cpu is a 3700+ amd 64, stock is at 2.2ghz and my overclock is at 2.8ghz, i am using the stock cooler, and a voltage bump from 1.40v to 1.47v was needed, now i dont think its the actual voltage that kills your cpu and mobo if you have a decent mobo, but its the temperature caused by the voltage increase, usually it shouldent matter if you have crap memory, my memory is just 2x 512mb or 1x 512mb generic crap, and all i do is lower the cpu to memory or fsb to memory ratio, cant remember which one it is, so at the moment, my memory is running at 420mhz, 20mhz over its normal speed, any further and i think it would be really bad for my memory, but i also had to lower the HT multiplyer setting in bios to 3x, any higher and the comp would freeze on bios becouse HT was going over 2ghz, as this is how the HT speed is determind i belive, FSB x HT multplyer x 2, and in my case it was, 254 x 3 x 2 which equals 1524mhz, to increase the cpu clock, you increase the FSB clock, but doing this also causes the memory to increase, thats why you gotta change the cpu to memory ratio or fsb to memory ratio, cant remember which one it is, but there are preset ratios, i either had mine at 420mhz or 333mhz i belive, nextr i had to change the voltage to 1.47v, i first tried 1.42v then 1.45v, 1.45v was ok but after long periods caused shutdown, i tried to get to 3ghz, i manged to get into windows, but it did not work in games, i had the voltage at 1.6v, NEVER go above 1.5v i say.

    The above is just really the steps i took to overclock, not somthing you should do exatly, i dont know if its even possible for you, as you motherboard is different, so maybe the overclocking options might be better, i am running on an Nforce 3 250gb mobo, from gigabyte, i think my cpu overclocked well to say that gigabyte aint aiming at overclocking boards.

    Also, my temperatures with my overclock were 29-30 idle and 39-42 load, the reading were took in winter tho.

    I hope some of this helps, just thought i would tell you how i oveclocked mine, might provide you with some usefull info :)
     

Share This Page